Question 1

Pre-Programmed & Automated

Accepted Answer

The device is automated with diodes emitting light on a specific surface area and lidar laser sensors to start sanitization while focusing energy on the surface with the most aggressive incidence angle that ensures maximum intensity is only directed towards pathogens, microbes, and bacteria.

Question 2

Red Marks the Spot

Accepted Answer

SNAP-Clean automatically calculates height to measure the necessary dosage time interval. Once a sanitization cycle is started, red light is emitted to alert from possible exposure. Fortunately, the UV-C LED technology requires no warm-up time, which makes it possible to frequently and swiftly sterilize a surface area within limited timeframes that are automatically calculated.

Question 3

Green Means Safe

Accepted Answer

Green lights are switched on when the surface area is fully sterilized. The adopted power of UV-C LED technology is highly effective against all infectious pathogens with a significantly higher efficacy in inactivating viruses’ chains of RNA when compared with chemical agents and mercury vapor UV lamps.

Question 4

Sustainability Maintained

Accepted Answer

SNAP-Clean does not produce ozone and requires minimal power with ZERO mercury involved. SNAP-Clean is a powerful alternative for mercury lamps and chemical agents that generate tons of waste every year. Thanks to its integrated UV-C LED technology, SNAP-Clean needs six times less energy than other solutions to reach 99.9% efficacy.

Question 5

Is UV-C radiation harmful to people and animals?

Accepted Answer

SAL Systems brings you safe and smart lighting solutions. Our  non-mercury based LED lighting system is concentrated in specific areas  of interaction, so surfaces and objects outside the marked area are not  exposed to the light. Our advanced laser Lidar sensors detect human  presence in a millisecond and automatically shut down the diodes,  preventing any potential eye irritation or skin harm that may occur from  prolonged exposure to powerful UV radiation. Experience the peace of  mind that comes with using safe and smart lighting technology.

Question 6

How do you make Credi-Clean safe?

Accepted Answer

The anchored installation method Developed by SAL Systems allows for smaller  light sources and reduces radiation exposure, ensuring the safety of  those nearby. The lights are focused on the exact areas where  disinfection is needed, providing precise control and avoiding any  "spill" onto surrounding areas. The motion sensors switch off the UV-C  light when motion is detected,  and will automatically power  down if no motion is detected for approximately 3 minutes, only powering  on when a valid movement trigger is detected. Trust SAL Systems for  efficient and safe disinfection.

Question 7

Why a device for a credit card terminal? what about the rest of the building?

Accepted Answer

Research shows a busy cashier could transact with around 300- 500 clients per shift, in certain cases up to 1000 per day! Taking into account that Viruses have been reported to survive on certain surfaces for up to 72 hours, it is vitally important that these high contact surfaces are continually cleaned. By automating the cleaning system, the risk is decreased. Other larger areas only have very few interactions per day, thus less risk.

Question 8

The COVID-19 pandemic has stabilized.  Will all these installations be necessary?

Accepted Answer

UVC is not new technology and has been used in food processing, water filtration, and hospitals for decades. UVC light has the ability to destroy the genetic material inside viruses and other microbes. These installations will help us continually prevent contact transmission of viruses and bacteria via credit card terminals.

Question 9

Will any Credit card machine work?

Accepted Answer

99 % of all produced and current credit card terminals will fit into the standard housing. For peculiar designs, we will happily do a modification

Question 10

Where is Credi-Clean made?

Accepted Answer

Credi-Clean Has been designed, patented, and manufactured in South Africa. There are various licensees globally that in some instances do part manufacture or assembly in order to create local employment while reducing the impact on the environment caused by additional freightage

Question 11

How long will it take for delivery?

Accepted Answer

We provide an OEM service and units can be branded and engraved with the client's colours and logos. in Most Cases product is held in stock.

Question 12

Is distributorship available?

Accepted Answer

Yes. We are currently looking for distributors and Licensees in many territories. Feel free to contact us to discuss your territory.

Frequently Asked Questions

Interested in becoming a licensee or distributor?

Documents

International Sales

Southern Africa Sales

Address

Licensee Locations